Saturday, August 29, 2015

SINGLE TO 3PHASE ELECTRIC POWER CONVERTER

buy phase converter now!! What is a Rotary phase converter?

A phase converter is simply a rotating motor, that converts single-phase power into 3-phase electricity to operate 3-phase equipment. Phase converters are typically applied where 3-phase is unavailable or too expensive to install. A properly sized and selected converter will operate any load just as well as 3-phase and will provide years of trouble-free service.


How does a rotary phase converter work?
A rotary phase converter is actually a rotating transformer. Through transformer action a phase converter splits off and phase shifts a portion of the single-phase supply from the utility creating true 3-phase power. When energized, the rotary phase converter uses the single-phase 2-line supply from the utility and creates a manufactured third line of power. The 3 lines (or phases) look identical to utility 3-phase with all three lines shifted 120°. The output of a rotary phase converter is true 3-phase. Each of the three output voltages will be shifted 120 electrical degrees. If the converter is properly sized, these voltages will remain in a balanced state over the entire range of connected loads.

the picture above show a simple phase converter
but for more stability and good performance and balanced output voltage we must add some capacitors as you can see in the picture later:
this is a simple and practical way to convert single phase to 3 phase and it will work very well
just make sure the quality of run capacitor must be very good and preferred oil filled capacitors
dont forget that the start capacitor must be connected only during start period so you can find any way you like to disconnect it after completing starting
and the final result must be like that:
then after completing building your converter before you connect it to the load make sure to measur the output so you can modify it by adding or removing some micro farads from the capacitor.



Thursday, August 27, 2015

A GUIDE TO BATTERY CHARGING

Your Title


A GUIDE TO BATTERY CHARGING
1.  CHARGING A BATTERY  7.  CE MARKING  
2.  3-STAGE CHARGING  8.  VOLTS, AMPS and WATTS
3.  TYPES OF CHARGER  9.  CHARGER SELECTION
4.  PROTECTION   10. DC-DC CONVERTERS
5.  REMOTE SENSING   11. INSTALLATION
6.  POWER FACTOR CORRECTION
 
1. Charging a Battery
There are many types of battery but batteries on boats are nearly always LEAD-ACID types -
similar to car batteries but heavier duty.
A BATTERY is made up of a number of CELLS.
A LEAD-ACID CELL generates around 2 volts. Small batteries contain 6 cells in a container
which add together to give 12 volts at the terminals. Larger cells are quite heavy and
individual CELLS are connected together 'in series' to make batteries of either 12 volt (6 cells)
or 24 volt (12 cells).
Although a battery is called a '12 volt' battery, its voltage varies from about 12.6 volts down to
10 volts when it is discharging and can rise to 15 or 16 volts during charging. It is very
important, however, to limit the maximum battery voltage during charging otherwise the
battery will be damaged. The battery voltage should not exceed 13.8 volts for long periods
and 14.4 volts for short periods (8 hours maximum). 
                       
2. 3-Stage Charging
There are two basic types of lead-acid battery charger: FLOAT chargers and 3-STAGE
CHARGERS. Float chargers also come in two versions - good ones and bad ones!
A good FLOAT charger charges the battery at a constant current until the 'FLOAT' voltage
(13.8V or 27.6V) is reached, then it progressively reduces the current to maintain that voltage.
This gets about 75% capacity back into the battery quickly but then takes a long time to
restore the other 25%. A bad FLOAT charger commences charging at the rated current but as the battery takes the
charge, its voltage rises and the current drops off long before the float voltage is reached.
Thus, even 75% capacity takes a long time to restore and full charge takes forever.
By far the best type of charger is the 3-STAGE CHARGER. This starts charging like a good
float charger but continues charging at constant current until the 'BOOST VOLTAGE' (14.4V
or 28.8V) is reached. Then, the current is progressively reduced until it drops to one quarter of
its maximum. This corresponds to 90% capacity in the battery. The charger voltage now
changes automatically to the float voltage where it then remains, slowly restoring the last 10%
capacity. Thus almost full charge is restored quickly and safely.
  
3. Types of Charger
There are several types of electronic circuitry used within battery chargers for the marine
market
3.1  FERRO-RESONANT (or CVT)
These use a low-frequency MAGNETIC control system, which makes them very HEAVY, very
BULKY and are also only available with a poor FLOAT charge characteristic, therefore very
SLOW recharging. They can also generate a large magnetic field which can upset other
equipment on board. On the plus side, they are CHEAP and RELIABLE due to the low
number of components used and they tend to appeal to boat-builders who put price at the top
of their list of priorities.

3.2  LINEAR CHARGERS
These also use a low-frequency transformer to reduce the input voltage to a lower level, but
they then use transistors to control the current and voltage fed to the battery. This technique
can be used for either FLOAT or 3-STAGE chargers but is very IN-EFFICIENT and therefore
HOT, HEAVY and BULKY. The biggest drawback is a LIMITED INPUT VOLTAGE range - not
ideal for running from a generator or some marina supplies.


3.3  SWITCHED MODE CHARGERS
These are more complicated than the previous two types and use the techniques perfected
for and now universally used in computers and televisions. The AC input is first turned into
high-voltage DC. It is then turned into high-frequency AC using special types of transistor and
a high-frequency transformer (one thirtieth the weight of a low-frequency transformer!)
reduces the voltage to the exact level needed to charge the battery. A sophisticated control
circuit produces an overall design with HIGH-EFFICIENCY, SMALL SIZE and LIGHT
WEIGHT. The extra complexity adds to the initial cost but results in lower running costs and
the ability to run from a SMALLER (and cheaper) GENERATOR if required. Switched mode
chargers can be either FLOAT or 3-STAGE types.
4. Protection
 Battery chargers should be designed to survive a number of fault conditions that can occur
during or after installation
4.1 SHORT-CIRCUIT OUTPUT can cause instant destruction or the charger may survive for
a few minutes or it may survive forever - it depends on how it was designed.
4.2 REVERSE BATTERY CONNECTION can be disastrous if suitable protection is not fitted.
A fuse is the simplest method. A relay is good at low output currents but is unreliable at higher
currents. Electronic methods are uneconomic at high currents.
4.3 OVER-TEMPERATURE PROTECTION is needed in case either the engine room
temperature exceeds the rated level or the ventilation of the charger is obstructed (air-flow
through a charger is essential to keep the electronic components cool).
4.4 OUTPUT OVER-VOLTAGE protection should be present in case of a fault in the charger
control circuit. Well-designed electronic circuits are very reliable but components can still
occasionally fail on a random basis. If this happens, a second circuit should prevent the
battery from receiving continuous over-charging.
 
5. Remote Sensing
5.1 TEMPERATURE SENSING
The FLOAT voltage of 13.8V/27.6V mentioned earlier is the ideal voltage at a battery
temperature of 25C. At higher temperatures this voltage should be progressively reduced by a
small amount. This is not much of a problem in the U.K. but in the Mediterranean, for
example, engine rooms can reach 40-45C and a charger for use at high temperatures should
have a remote temperature sensing facility. This consists of a small sensing block which is
affixed to the battery and a cable connecting it to the battery charger.


5.2 VOLTAGE SENSING
The thickness of cables joining a charger to a battery should be chosen to keep the voltage
drop on the cable very low. However, any drop in the cable will increase the re-charging time
to some extent. For the ultimate performance, the charger should control the voltage at the
battery not at the charger. This is achieved by taking a thin cable from the battery positive
terminal to a remote voltage sense terminal on the charger. Some chargers have this feature,
others do not. It becomes increasing important at higher currents.
 6. Power Factor Correction (PFC)
Although the AC mains voltage is a smoothly-changing waveform called a SINE-WAVE, the
current taken from the mains by most battery chargers, T.V.s and computers consists of
narrow peaks of current. This is inefficient for the power generating companies and, with the
proliferation of T.V.s and computers in particular, the EC have considered enforcing the
addition of an extra circuit called a POWER FACTOR CORRECTION circuit to smooth out the
peaks. The date for introduction of this has already been postponed twice but it will eventually
become compulsory. In the meantime, PFC is beneficial on a boat because it uses the mains
power very efficiently and will therefore run from a smaller generator or poor marina supplies
which non-PFC chargers might struggle with.

7. CE Marking
In January 1996, the EC introduced new legislation which required battery chargers to meet
certain standards before being sold within the EC. The regulations cover the amount of radio
frequency interference produced, the immunity of the charger to RFI from other sources, dips
and surges in the mains and immunity to electrostatic discharge. Conformity to these
specifications is indicated by attaching a CE label to the charger
.
8. Volts, Amps and Watts
WATTS are the units of POWER. A hairdryer full-on might be 500 WATTS; on the low-power
setting it might be 200 WATTS.
The higher the POWER the bigger the charger.
VOLTAGE must be matched to the equipment in use and will be either 12 VOLTS or 24
VOLTS in a boat.
CURRENT indicates the flow of energy from the battery and is measured in AMPERES (or
AMPS). Zero current and the battery is not discharging. The higher the current the faster the
battery will discharge.
A battery is rated in AMPERE-HOURS (abbreviated Ah) and this is called the BATTERY
CAPACITY. For example, a small boat might have a 12 volt 100Ah battery. This battery will
provide 100 AMPERE-HOURS before needing to be re-charged. This may be taken from the
battery as
1 AMP for 100 hours
2 AMPS for 50 hours
10 AMPS for 10 hours etc.
WATTS are VOLTAGE multiplied by CURRENT, so taking the above example with the 12 volt
battery
1 AMP x 12 VOLTS = 12 WATTS for 100 hours
2 AMPS x 12 VOLTS = 24 WATTS for 50 hours 10 AMPS x 12 VOLTS = 120 WATTS for 10 hours
Re-charging a battery follows the same principle. The requirement is usually to re-charge the
battery over-night - say in 10 hours. 
Because a battery is not totally efficient at converting electrical energy into chemical energy
and vice-versa, re-charging a 100Ah battery requires about 120Ah to be put back into it, and
this can be achieved by either
120 Amp-hours / 10 hours = 12 Amps for 10 hours
120 Amp-hours / 15 hours = 8 Amps for 15 hours
120 Amp-hours / 24 hours = 5 Amps for 24 hours etc.
CURRENT = WATTS / VOLTS
therefore if, say, the lights add up to 36 WATTS and the battery VOLTAGE is 12 VOLTS then
the CURRENT taken from the battery will be
36 WATTS / 12 VOLTS = 3 AMPS
If these lights are on whilst the battery is being charged, then the battery charger must also
provide an extra 3 AMPS to power them.
 9. Battery Charger buy battery charger her !!! Selection By Calculation Example
Below is a sample calculation to determine which of our products would best suit your
requirements. 
1. Determine the battery voltage - 12 volt or 24 volt
2. Determine how many batteries are to be charged (1,2,3 or 4)
3. What are the battery capacities (Ah, Amp-hours)?
Add them together
e.g. 2 x 60Ah, 1 x 100Ah = 220 Ah total
4. What re-charge time is required?
(6 hours minimum, usually 24 hours maximum - if not known, assume 10 hours)
5. Divide TOTAL Ah by the re-charge time to get CHARGING CURRENT
e.g. 220Ah / 10 hours = 22 AMPS.
6. ADD 20% to allow for battery in-efficiency
i.e. 22 AMPS + 20% = 26.4 AMPS
7. Is there any additional load current on the battery during re-charging? If so, add this to the
CHARGING CURRENT.
e.g. 24 WATTS / 12 VOLTS = 2 AMPS
CHARGER CURRENT REQUIRED = 26.4 AMPS + 2 AMPS = 28.4 AMPS.
8. Choose the next biggest charger in the range
e.g. 12 VOLT, 30 AMP, 3 BATTERY BANKS = BCM 12/30-3
Note:
Much too big a charger could damage the battery and too small will take longer to re-charge.
 10. DC-DC Converters
-Some equipment is only available for 12 volt operation. If the boat's main battery is 24 volt,
there are three options to run 12 volt equipment on board
1.Install a separate 12 volt battery with its own 12 volt mains battery charger.
2.Use a DC-DC converter to generate 12 volts using energy from the main 24 volt battery.
3.Install a separate 12 volt battery and charge it using a DC-DC converter from the main 24
volt battery. This requires a 13.8 volt output converter designed for the purpose.
For options 2 and 3 it is useful to have a remote on/off switch otherwise the DC-DC converter
could drain the 24 volt battery whenever the 24 volt battery is not being charged.
11. Battery Charger Installation
1. The INPUT to the charger is AC mains voltage and is capable of causing death. A circuit
breaker of suitable rating MUST be fitted between the charger and the shore power in
accordance with good marine installation practice. If the charger is replacing an existing
charger, then this should already be in place.
2. The BATTERY itself stores large amounts of energy and is quite capable of causing a fire
or explosion if the output terminals are shorted together. Extreme care must be taken when
wiring the charger to the battery. Cables should be of suitable thickness for the current rating
for the charger, cable runs should be kept as short as possible and all cables must be
securely held in place with cable fixings to prevent wear to the cable insulation.
3. The charger should be securely fixed to a vertical surface using ALL mounting hole
positions ( 3 for BCM, 4 for BCH and BCO).
4. At least 75mm clearance must be left all around the charger to allow the free flow of air over the
charger. The ventilation holes or slots must not be obstructed in any way.
5. The chargers should be protected from water and spray.